联系我们

English: +(86) 13823446125

WeChat: 13823446125

中国区代理: 13802685284

电动卷闸门电机接线图Electric Rolling Gate Motor Wiring Diagram

电动卷闸门电机接线图

电动卷帘门电机的接线图结构非常重要,对于确保电机的正常运行和安全使用至关重要。以下将详细介绍电动卷帘门电机的接线结构原理和步骤。

1. 接线结构原理

电动卷帘门电机的工作原理就是普通的可逆控制电路。操作按钮有“上”、“下”、“停止”。卷帘门电动机的可逆控制电路,还必须安装上、下限位开关,和极限保护开关作为保护装置。电脑控制的卷帘门电动机的可逆控制电路,也是依靠可逆接触器来运行的。

The working principle of the electric roller shutter motor is based on a reversible control circuit, operated through buttons labeled “Up,” “Down,” and “Stop.” The reversible control circuit for the roller shutter motor must also include upper and lower limit switches, and an extreme protection switch as safety devices. The computer-controlled roller shutter motor’s reversible control circuit also relies on reversible contactors to operate.

2. 接线图详解

电动门的升降是利用两个继电器和一个三联按钮控制,继电器启动吸合后自保到达上限后利用机械位置开关的左右运动控制门上下的限位控制。

The raising and lowering of the electric door are controlled using two relays and a three-button control panel. Once the relay is activated, it remains engaged until the upper limit is reached, controlled by the movement of mechanical position switches.

3. 接线操作步骤

根据卷帘门电机接线图,将电源线、控制线、电机线分别接到电机的相应端子上。具体操作步骤如下:

  • 将电源线的火线和零线分别接到电机的L和N端子上。
  • 将控制线的开关线和接地线分别接到电机的COM和GND端子上。
  • 将电机线的相线和中线分别接到电机的U和V端子上。

According to the wiring diagram of the roller shutter motor, connect the power lines, control lines, and motor lines to the corresponding terminals on the motor. The specific steps are as follows:

  • Connect the live wire and neutral wire of the power supply to the L and N terminals of the motor.
  • Connect the switch line and ground wire of the control line to the COM and GND terminals of the motor.
  • Connect the phase line and middle line of the motor line to the U and V terminals of the motor.

4. 单相电机接线

卷帘门电机是单相电机,接线图如下:S为电机转向转换开关。

The roller shutter motor is a single-phase motor. The wiring diagram is as follows: S is the motor direction change switch.

5. 接触器的选择

接线直接看图,其实完全没有必要使用继电器,因为接触器选型时起码都是10A的电流。继电器用CJ10-10就ok了,选CJX4-09。意思是接触器也不要,就像开灯一样直接导通就行了。如果非要用的话,就像图中画的一样,使用两个接触器,其中用接触器辅助触点进行互锁和自锁。

When wiring directly according to the diagram, relays are not necessarily required since contactors of at least 10A are typically selected. Relays like CJ10-10 or contactors like CJX4-09 are sufficient. This means contactors might not be needed, and direct conduction like a light switch might suffice. If used, employ two contactors as shown in the diagram, utilizing auxiliary contacts for interlocking and self-locking.

6. 卷帘门电机的运行

机带动卷帘中心轴转动,达到卷帘开关,当转动到电机设定的上下限位时自动停止。对齿轮,就是调上、下限位,也就是确定卷帘门平时开到的最高位置和下降到的最低位置,这是要靠调整卷门机上的限位器来确定的。

The motor drives the central axis of the roller shutter to rotate, achieving the opening and closing of the shutter. It automatically stops when it reaches the upper and lower limits set by the motor. Adjusting the gears sets the upper and lower limits, determining the maximum opening and lowest position of the roller shutter, which is controlled by adjusting the limiters on the roller shutter motor.

东荣电动卷帘门电机的接线图如下,通过了解这个接线图,用户可以更好地安装和使用卷门帘电机。这种电机的工作原理是基于可逆控制电路,操作按钮包括“上”、“下”、“停止”三种。无论是卷门帘电机还是 roller shutter motor,都需要在电机的接线过程中安装上、下限位开关以及极限保护开关,以确保其安全运行。

By understanding the wiring diagram of the Dongrong roller shutter motor, users can better install and use the rolling shutter motor. This type of motor operates on a reversible control circuit, with operation buttons including “Up,” “Down,” and “Stop.” Whether it’s a 卷门帘电机 or a roller shutter motor, upper and lower limit switches, as well as extreme protection switches, must be installed in the motor wiring process to ensure safe operation.