联系我们

English: +(86) 13823446125

WeChat: 13823446125

中国区代理: 13802685284

电动卷帘门手摇孔及其安装与保养Electric rolling door hand hole and its installation and maintenance

电动卷帘门手摇孔及其安装与保养指南

电动卷帘门是一种现代化的门类,它在提升便利性的同时也带来了许多新的使用技巧和保养方法。本文将详细介绍电动卷帘门手摇孔的位置及其使用方法,并探讨电动卷帘门的安装和保养技巧。

Where is the Manual Override Hole of Electric Roller Shutter Door? The manual override hole of an electric roller shutter door is typically located near the roller shaft. When there is a power outage, this hole can be used to manually operate the door. By pulling the brake cable down, the brake clutch can be disengaged from the motor. Then, connect the manual crank to the motor and use it to operate the door. When power is restored, ensure the motor brake is reset.

一、电动卷帘门手摇孔的位置

电动卷帘门的手动转换开关通常位于卷轴附近。当电动卷帘门停电时,可以通过手摇孔来升降卷帘门。具体操作步骤如下:首先,将刹车钢索向下拉,使刹车离合器与马达脱离;然后,将摇杆连接头与马达相连接,使用手动摇杆进行卷门操作;最后,恢复供电时,确保马达刹车器复位。

二、电动卷帘门的安装方法

  1. 设计与测量:首先,在需要安装的门框框口位置画线,标明尺寸大小。然后,联系专业工作人员设计合适的电动卷帘门。门框内部高度应比门扇的高度稍高一些。
  2. 固定门框:先将电动卷帘门的门框固定好,拆掉门框下部的固定板,预留地面凹槽,固定木楔,并将门框铁脚与预埋铁板件焊牢。
  3. 安装门扇:将电动卷帘门的主体门扇安装好,确保门与墙体紧密结合,密封性良好,然后对洞口及墙体进行粉刷。
  4. 调整与检验:粉刷完毕后,检查门缝是否均匀平整,确保电动卷帘门开启和关闭时自如轻便,不出现过紧、过松或反弹等问题。

Installation Method of Electric Roller Shutter Door

  1. Design and Measurement: Draw lines at the door frame where the door will be installed, indicating the size. Consult with professionals to design a suitable electric roller shutter door. The internal height of the door frame should be slightly higher than the door panel.
  2. Fixing the Door Frame: Secure the door frame first, remove the bottom fixing plate of the frame, reserve ground grooves on both sides of the opening, fix wooden wedges, and weld the iron feet of the door frame to the embedded iron plates.
  3. Installing the Door Panel: Install the main door panel of the electric roller shutter door, ensuring it integrates well with the wall and has good sealing. Then, plaster the opening and wall.
  4. Adjusting and Inspecting: After plastering, check that the door seams are even and smooth, ensuring the electric roller shutter door opens and closes smoothly without being too tight, loose, or bouncing.

三、车库电动卷帘门的保养方法

  1. 保持电压稳定:在使用电动卷帘门的过程中,要尽量保持控制器和电压的稳定,禁止将电动卷帘门安装在潮湿环境中。此外,不要随意打开遥控器。如果发现门体上有电线缠绕、打结等情况,应及时处理。注意通道是否堵塞,以防止门体下降受阻,如发生异常应立即停止电机运作。
  2. 润滑与调整:经常检查电动卷帘门上下行程的开关,并在行程控制器上加润滑油,保持其正常运行。此外,还要检查手动控卷帘门的控制器运行情况,校对上下行程开关位置,确保电动卷帘门开启或关闭时处于适当位置。在检查过程中,防止电动卷帘门冲顶或冲底,或发生反转情况。如出现紧急情况,应立即切断电源,停止电动卷帘门的转动。
  3. 检查与维护:使用电动卷帘门时,应经常检查电动卷帘门的手动开关和手动升降装置,以防止在紧急情况下失灵,避免造成安全事故。
  4. 清理与润滑:保持卷帘门轨道的畅通,及时清理轨道内的灰尘和杂物,确保内部清洁。定期为卷帘门电机和传动链条添加润滑剂,使其开关顺畅。检查控制箱内的器件和开关控制盒,紧固接线端口和螺丝,清洁控制箱内外表面和按钮上的灰尘,防止按钮卡住而无法反弹。

Maintenance of Garage Electric Roller Shutter Door

  1. Maintaining Voltage Stability: During the use of the electric roller shutter door, try to keep the controller and voltage stable. Do not install the electric roller shutter door in a very humid environment and avoid randomly opening the remote control. If you find wires wrapped around or knotted on the door body, deal with it promptly. Pay attention to whether the passage is blocked, preventing the door body from descending. If there is any abnormal response, stop the motor operation immediately.
  2. Lubrication and Adjustment: Regularly check the upper and lower travel switches of the electric roller shutter door and lubricate the travel controller to maintain normal operation. Also, check the manual control of the roller shutter door and calibrate the upper and lower travel switch positions, ensuring the electric roller shutter door is in the appropriate position when opening or closing. During inspection, prevent the electric roller shutter door from hitting the top or bottom or reversing. If an emergency occurs, cut off the power immediately to stop the door.
  3. Inspection and Maintenance: Frequently check the manual switch and manual lifting device of the electric roller shutter door to prevent failure in emergencies and avoid unnecessary safety accidents.
  4. Cleaning and Lubrication: Keep the track of the roller shutter door running smoothly, clean the track in time, and maintain internal cleanliness. Regularly lubricate the motor and transmission chain of the roller shutter door to ensure smooth operation. Check the components and switch control box inside the control box, tighten the wiring ports and screws, and clean the dust and dirt on the control box surface and buttons to prevent the buttons from getting stuck.